CLEANING YOUR
RECOMMENDED CLEANERS FOR EACH MOBIUS PART:
It is recommended that warm or hot water is used to make up your diluted cleaning solution for the Mobius.
BLADE SYSTEM
(Helical Blades, Bed Knives, Spacer Bars)
RECOMMENDED PH RANGE OF CLEANER
8.5 – 10
RECOMMENDED CLEANER(S)*
STEP 1 – CLEAN
– Tub O’ Towels Heavy Duty Cleaning Wipes and/or
– RESIN8 XTRA.
STEP 2 – RINSE
– with water
STEP 3 - SANITIZE (if necessary)
– Shyield or Isopropyl
RECOMMENDED CLEANING PROCEDURE
BED KNIVES & SPACER BARS:
With parts on racks, soak in diluted cleaning solution for 5 – 10 minutes, brush/wipe down any areas with significant resin build-up then rinse. Pressure washer OK.
HELICAL BLADES:
Place helical blades in blade racks. If resin build-up is minimal, simply wipe down with cleaning wipe or cloth. If resin build-up is more significant, spray blades with cleaner, avoiding the bearings on either end, and let sit for 5 minutes. Brush/wipe down any areas with significant resin build-up then rinse. Pressure washer OK on blades, but not on bearing blocks.
To clean bearing blocks, place blades on support racks. Use a cleaning wipe to hand-clean bearing blocks, as necessary.
SEPARATOR
FAN HOUSING
(Stainless Steel Versions)
RECOMMENDED PH RANGE OF CLEANER
10 – 13
RECOMMENDED CLEANER(S)*
STEP 1 – CLEAN
– Super Clean
– Tub O’ Towels Heavy Duty Cleaning Wipes and/or
– RESIN8 XTRA.
STEP 2 – RINSE
– with water
STEP 3 - SANITIZE (if necessary)
– Shyield or Isopropyl
RECOMMENDED CLEANING PROCEDURE
Spray with diluted cleaning solution, let sit for 5 – 10 minutes, brush/wipe down any areas with significant resin build-up then rinse. Pressure washer OK.
SEPARATOR HOUSING
FAN HOUSING
(Anodized Aluminum Versions)
RECOMMENDED PH RANGE OF CLEANER
8.5 – 10
RECOMMENDED CLEANER(S)*
STEP 1 – CLEAN
– Tub O’ Towels Heavy Duty Cleaning Wipes and/or
– RESIN8 XTRA.
STEP 2 – RINSE
– with water
STEP 3 - SANITIZE (if necessary)
– Shyield or Isopropyl
RECOMMENDED CLEANING PROCEDURE
Spray with diluted cleaning solution, let sit for 5 – 10 minutes, brush/wipe down any areas with significant resin build-up then rinse. Pressure washer OK.
LID SCREENS
BLUE TUMBLER RETAINING RINGS
RECOMMENDED PH RANGE OF CLEANER
8.5 – 10
RECOMMENDED CLEANER(S)*
STEP 1 – CLEAN
– Tub O’ Towels Heavy Duty Cleaning Wipes and/or
– RESIN8 XTRA.
STEP 2 – RINSE
– with water
STEP 3 - SANITIZE (if necessary)
– Shyield or Isopropyl
RECOMMENDED CLEANING PROCEDURE
Spray with diluted cleaning solution, let sit for 5 – 15 minutes, brush/wipe down areas with significant resin build-up then rinse. Pressure washer OK.
MOBIUS BODY & LID
RECOMMENDED PH RANGE OF CLEANER
8.5 – 10
RECOMMENDED CLEANER(S)*
STEP 1 – CLEAN
– Tub O’ Towels Heavy Duty Cleaning Wipes and/or
– RESIN8 XTRA.
STEP 2 – RINSE
– with water
STEP 3 - SANITIZE (if necessary)
– Shyield or Isopropyl
RECOMMENDED CLEANING PROCEDURE
Spray areas that require cleaning with diluted cleaning solution. Allow cleaner to sit for 5 – 10 minutes, then wipe down with a cleaning wipe or soft cloth. For areas with significant resin buildup, a plastic razor blade can be used to scrape off resin before wiping down.
Note 1: Do not pressure wash Mobius body and avoid spraying control panel and other electrical components.
Note 2: Use compressed air to blow down gears and belts on left side of machine.
TUMBLER
BRUSH
RECOMMENDED PH RANGE OF CLEANER
10 – 13
RECOMMENDED CLEANER(S)*
STEP 1 – CLEAN
– Super Clean
– Tub O’ Towels Heavy Duty Cleaning Wipes and/or
– RESIN8 XTRA.
STEP 2 – RINSE
– with water
STEP 3 - SANITIZE (if necessary)
– Shyield or Isopropyl
RECOMMENDED CLEANING PROCEDURE
AUTOMATIC TUMBLER & BRUSH WASHER:
Add 1 part cleaner to 4 parts hot water, turn on, allow tumbler and brush to rotate for 5-10mins. Rinse with water. Apply sanitizer.
MANUAL CLEANING:
Soak in diluted cleaning solution for 5 – 15 minutes, brush/wipe down any areas with significant resin build-up then rinse. Pressure washer OK.
TRIM TOTE
TRIM TOTE GASKET
RECOMMENDED PH RANGE OF CLEANER
10 – 13
RECOMMENDED CLEANER(S)*
STEP 1 – CLEAN
– Super Clean
– Tub O’ Towels Heavy Duty Cleaning Wipes and/or
– RESIN8 XTRA.
STEP 2 – RINSE
– with water
STEP 3 - SANITIZE (if necessary)
– Shyield or Isopropyl
RECOMMENDED CLEANING PROCEDURE
Spray with or soak in diluted cleaning solution for 5 – 15 minutes, brush/wipe down any areas with significant resin build-up then rinse. Pressure washer OK.
IMPELLER FAN
RECOMMENDED PH RANGE OF CLEANER
10 – 13
RECOMMENDED CLEANER(S)*
STEP 1 – CLEAN
– Super Clean
– Tub O’ Towels Heavy Duty Cleaning Wipes and/or
– RESIN8 XTRA.
STEP 2 – RINSE
– with water
STEP 3 - SANITIZE (if necessary)
– Shyield or Isopropyl
RECOMMENDED CLEANING PROCEDURE
Wipe down impeller blades with a cleaning wipe or cloth, then rinse.
FAN HOUSING FILTER BAG
(200 mesh)
RECOMMENDED PH RANGE OF CLEANER
10 – 13
RECOMMENDED CLEANER(S)*
STEP 1 – CLEAN
– Super Clean
– Tub O’ Towels Heavy Duty Cleaning Wipes and/or
– RESIN8 XTRA.
STEP 2 – RINSE
– with water
STEP 3 - SANITIZE (if necessary)
– Shyield or Isopropyl
RECOMMENDED CLEANING PROCEDURE
Soak in diluted cleaning solution for 5 – 15 minutes, then rinse. Pressure washer OK.
FAN HOUSING FILTER BAG
(MERV 8 Material)
RECOMMENDED PH RANGE OF CLEANER
N / A
RECOMMENDED CLEANER(S)*
Compressed Air
RECOMMENDED CLEANING PROCEDURE
In a well-ventilated area, use compressed air to blow out the filter bag. Note, filter bag should be replaced on a regular basis.
